高圧配管システムにおいて, 漏れ防止は最優先事項です. 石油でもガスでも, 石油化学, 発電, または水処理産業, a system’s ability to maintain a tight seal can directly impact safety, 効率, 規制遵守と. One often overlooked but critical factor in achieving a reliable seal is the flange face roughness.

の roughness of the flange face surface affects how the gasket interacts with the metal, how evenly pressure is distributed, and whether a long-lasting seal can be maintained under fluctuating temperature and pressure conditions. In this comprehensive SEO article, ササフランジ explains what flange face roughness is, なぜそれが重要なのか, the standards governing it, and how to choose the right finish for your application.

---

What Is Flange Face Roughness?

Flange face roughness を指します microscopic texture or finish of the sealing surface on a pipe flange. It is measured as the average roughness (ラ) または arithmetic mean roughness height, typically expressed in microinches (µin) または micrometers (μm).

Roughness affects how the gasket material conforms to the flange surface. A surface that is too smooth may not allow enough grip for the gasket, leading to slip or leakage. A surface that is too rough may cause damage to the gasket and result in imperfect sealing.

で ササフランジ, we apply precision machining processes to ensure that flange face finishes meet or exceed industry sealing requirements.

---

Common Flange Face Types and Roughness Levels

Flanges are manufactured with various face types, each with a recommended surface roughness depending on the application and gasket type.

1. 盛り上がった顔 (RF)

The most common flange face type. The sealing area is a raised ring on the flange face.

• Typical roughness: 125–250AARH (Average Arithmetic Roughness Height)

• Compatible with spiral wound, jacketed, and compressed fiber gaskets

2. 平面 (FF)

The entire face is a flat, 連続シール面.

• Typical roughness: 125–250AARH

• Used mainly in low-pressure systems or when mating with cast iron flanges

3. リング型ジョイント (RTJ)

Uses a metal-to-metal seal between a grooved flange and a metallic ring gasket.

• Typical roughness: ≤ 63 ああ

• Requires smooth finishes to ensure precise contact

4. 舌 & 溝 / Male-Female

Machined interlocking faces; ideal for high-sealing integrity.

• Typical roughness: 64–125 AARH

• Often used in high-pressure or hazardous fluid services

で ササフランジ, we can supply flanges with customized face finishes to meet specific gasket and pressure class requirements.

---

Why Flange Face Roughness Matters for Sealing

1. Sealing Performance and Gasket Bite

The ideal flange face provides the gasket with enough “bite” to grip and deform slightly into the roughness profile. This deformation is critical to form a seal that prevents the passage of fluids or gases. If the surface is too smooth, the gasket may not seat properly. If it’s too rough, it could tear the gasket or create leak paths.

2. Load Distribution

Surface roughness affects how bolt load is transferred to the gasket. Uniform roughness ensures even compression of the gasket material. Uneven or damaged surfaces can lead to localized stresses, which compromise sealing effectiveness.

3. Gasket Type Compatibility

Different gaskets are designed to work with different levels of flange face roughness:

• ソフトガスケット (例えば, compressed non-asbestos fiber, PTFE): Work better with smoother surfaces

• メタルガスケット (例えば, 螺旋状の傷, ring joint): Need higher roughness for grip and seal integrity

Choosing the wrong face finish for the gasket type can lead to premature gasket failure.

4. Pressure and Temperature Resistance

In high-pressure or high-temperature systems, flange surface conditions become even more important. Any irregularities can expand under heat or pressure, leading to long-term degradation of the seal.

---

Industry Standards for Flange Face Roughness

Flange face roughness is governed by several international standards to ensure uniformity and compatibility:

• ASME B16.5
  Recommends a surface finish of 125–250 AARH for raised and flat faces.

• ASME B16.47
  For large-diameter flanges, also specifies 125–250 AARH.

• API 6A
  For RTJ flanges used in the petroleum industry, surface roughness should be smoother than 63 ああ.

• EN 1092-1
  Uses Ra values, typically 3.2–6.3 µm for Type A faces.

で ササフランジ, we machine all flange faces according to these standards and can provide inspection certificates to confirm compliance.

---

How Flange Face Roughness Is Measured

The most common method to measure surface roughness is using a 表面形状計, which drags a fine stylus over the surface and records the vertical deviations over a set distance.

• ラ (Roughness Average): Arithmetic average of the absolute values of the surface profile

• Rz: Maximum peak-to-valley height in a sample length

• ああ: An older unit, roughly equivalent to Ra (1 µm ≈ 39 ああ)

Measurements are taken at several points on the flange face to ensure uniformity. で ササフランジ, we offer roughness inspection reports on request for critical sealing applications.

---

Factors That Can Affect Flange Face Roughness

1. Tool Wear During Machining

Worn tools may produce uneven or inconsistent finishes on the flange face, increasing the risk of leaks. That’s why precision machining and regular tool calibration are critical.

2. Improper Storage or Handling

Flanges that are scratched, dented, or corroded during storage can lose their surface integrity. Protective packaging and handling procedures help maintain the original roughness.

3. Gasket Imprints and Reuse

Flanges that have been used before may show gasket imprints or surface damage, especially with metallic gaskets. These surfaces must be inspected and re-machined if needed before reuse.

4. Contamination or Residue

Oils, さび, or debris on the sealing surface can interfere with proper gasket seating. Surfaces must be cleaned thoroughly インストール前に.

---

Best Practices for Flange Sealing Success

• Select the right flange face finish based on gasket type and operating conditions

• Never mix face types (例えば, do not mate an RF flange with an RTJ flange)

• Inspect surface roughness before assembly, especially on high-pressure flanges

• Avoid reusing damaged flanges without proper re-machining

• Use calibrated torque wrenches to apply even bolt load

で ササフランジ, we offer expert consultation to help customers choose the right flange-gasket combinations and ensure long-lasting seals.

---

Documentation and Certification

全て ササフランジ products can be supplied with:

• EN10204 3.1 証明書

• Dimensional and roughness reports

• Visual inspection and NDT records

• ASMEへの準拠, DIN, EN, および API 標準

Our certificates include actual measured roughness values, ensuring full transparency and quality control.

---

結論

Flange face roughness is not a minor detail—it’s a major factor in achieving effective and leak-proof seals. Understanding the correct surface finish for your flange face ensures better gasket performance, increased system reliability, and long-term operational safety.

で ササフランジ, we are committed to providing precision-machined flanges that meet international roughness standards and exceed customer expectations. Whether you need standard RF flanges or specialized RTJ components, our team delivers quality you can trust.