How to Measure Flange Size?
Quick Answer
To measure an unknown flange, record its outside diameter, bore, bolt-circle diameter (PCD/BCD), bolt-hole count and diameter, rim thickness, face type and raised-face height where applicable. Also identify the flange type and matching pipe bore or schedule. Do not assign an NPS/DN or pressure class from one dimension alone: compare the complete set with the exact dimensional standard and edition.
Jump to the flange measurement checklist
Flange Measurement Checklist
| Dimension or feature | How to measure it | Why it matters |
|---|---|---|
| Outside diameter (OD) | Measure edge to opposite edge through the centre. | Helps narrow the standard, nominal size and class/PN. |
| Bore / inside diameter | Measure the clear opening; also note any hub and flange type. | Bore is not always the nominal pipe size and may depend on schedule or machining. |
| Bolt-circle diameter (PCD/BCD) | Measure centre-to-centre across two opposite holes when possible. | Controls alignment with the mating flange. |
| Bolt holes | Count the holes and measure one hole diameter with a caliper. | Hole count and size distinguish otherwise similar patterns. |
| Thickness | Measure the rim/body thickness; record hub dimensions separately. | Thickness varies by standard, size, rating and flange type. |
| Face | Identify RF, FF, RTJ or another face; measure raised-face height separately. | The face must match the gasket and mating-joint design. |
Step-by-Step: How to Measure Flange Size
- Make the system safe. Isolate, depressurize and obtain permission before measuring installed piping. Do not loosen bolting for identification.
- Clean only enough to expose edges and markings. Preserve stamped information and avoid damaging the sealing face.
- Record markings first. Photograph the standard, size, class/PN, material and manufacturer marks when legible.
- Measure the face. Record OD, bore and face type using a suitable rule, tape, caliper or depth gauge.
- Measure the bolt pattern. Count holes, measure hole diameter and determine PCD/BCD.
- Measure the profile. Record rim thickness, raised-face height and hub dimensions if present.
- Compare the complete set. Match all dimensions to one standard, edition, size, rating and flange type; resolve any mismatch before ordering.
How to Determine the Bolt-Circle Diameter
For an even number of equally spaced holes, measure centre-to-centre between two directly opposite holes. If only adjacent hole centres are accessible, measure the chord c, count the holes n, and calculate PCD = c / sin(180° / n). Repeat the measurement in more than one direction because corrosion, distortion or field modification can mislead a single reading.
Which Dimensional Standard Should You Check?
ASME B16.5 covers pipe flanges and flanged fittings within its published NPS 1/2 through NPS 24 scope. ASME B16.47 covers large-diameter steel flanges within NPS 26 through NPS 60. EN 1092-1 and other regional standards use different designation systems. Use the project-specified standard and edition; “ANSI flange” alone is not a complete purchasing description.
What to Send for Identification or Quotation
- clear face, side-profile and marking photographs;
- OD, bore, thickness and raised-face height;
- PCD/BCD, bolt-hole count and hole diameter;
- flange type and face type;
- pipe OD and schedule/bore where relevant;
- service fluid, design pressure and temperature;
- required material specification, certificates and quantity.
Verified Product Starting Points
Use these product pages as quotation starting points; measurement alone does not confirm grade or service suitability.
Frequently Asked Questions
Is flange size the same as outside diameter?
No. Nominal size is a designation, not the measured flange OD. Confirm the full dimensional pattern.
Can I infer the pressure class from thickness?
Not reliably. Compare thickness together with OD, bolt pattern, face, type and bore against the specified standard and edition.
Should I measure a flange while the line is pressurized?
Only follow the site’s approved safety procedure. Never loosen bolting or disturb a live joint for identification.
Primary References
- ASME B16.5 — published scope for pipe flanges and flanged fittings.
- ASME B16.47 — published scope for large-diameter steel flanges.
Need Help Identifying a Flange?
Send the measurements, marking photos, face/type, quantity and service conditions. We can compare the information with the requested standard before quotation.

No Comments