How to Measure Flange Size?

Quick Answer

To measure an unknown flange, record its outside diameter, bore, bolt-circle diameter (PCD/BCD), bolt-hole count and diameter, rim thickness, face type and raised-face height where applicable. Also identify the flange type and matching pipe bore or schedule. Do not assign an NPS/DN or pressure class from one dimension alone: compare the complete set with the exact dimensional standard and edition.

Jump to the flange measurement checklist

Flange dimensions to measureFront and side schematic showing outside diameter, bolt circle, bore, bolt-hole diameter, thickness and raised-face height.ODPCD / BCDBoreThicknessOD profileRaised faceBolt-hole ØFront viewSide profile
Measure the full pattern and profile; this schematic is not a dimensional standard.

Flange Measurement Checklist

Dimension or feature How to measure it Why it matters
Outside diameter (OD) Measure edge to opposite edge through the centre. Helps narrow the standard, nominal size and class/PN.
Bore / inside diameter Measure the clear opening; also note any hub and flange type. Bore is not always the nominal pipe size and may depend on schedule or machining.
Bolt-circle diameter (PCD/BCD) Measure centre-to-centre across two opposite holes when possible. Controls alignment with the mating flange.
Bolt holes Count the holes and measure one hole diameter with a caliper. Hole count and size distinguish otherwise similar patterns.
Thickness Measure the rim/body thickness; record hub dimensions separately. Thickness varies by standard, size, rating and flange type.
Face Identify RF, FF, RTJ or another face; measure raised-face height separately. The face must match the gasket and mating-joint design.

Step-by-Step: How to Measure Flange Size

  1. Make the system safe. Isolate, depressurize and obtain permission before measuring installed piping. Do not loosen bolting for identification.
  2. Clean only enough to expose edges and markings. Preserve stamped information and avoid damaging the sealing face.
  3. Record markings first. Photograph the standard, size, class/PN, material and manufacturer marks when legible.
  4. Measure the face. Record OD, bore and face type using a suitable rule, tape, caliper or depth gauge.
  5. Measure the bolt pattern. Count holes, measure hole diameter and determine PCD/BCD.
  6. Measure the profile. Record rim thickness, raised-face height and hub dimensions if present.
  7. Compare the complete set. Match all dimensions to one standard, edition, size, rating and flange type; resolve any mismatch before ordering.

How to Determine the Bolt-Circle Diameter

For an even number of equally spaced holes, measure centre-to-centre between two directly opposite holes. If only adjacent hole centres are accessible, measure the chord c, count the holes n, and calculate PCD = c / sin(180° / n). Repeat the measurement in more than one direction because corrosion, distortion or field modification can mislead a single reading.

Do not identify a flange by OD alone. Different standards, classes and flange types can share or nearly share one dimension. Bore and thickness may also change with schedule, type or machining. The old universal “4-inch Class 150” example has therefore been removed.

Which Dimensional Standard Should You Check?

ASME B16.5 covers pipe flanges and flanged fittings within its published NPS 1/2 through NPS 24 scope. ASME B16.47 covers large-diameter steel flanges within NPS 26 through NPS 60. EN 1092-1 and other regional standards use different designation systems. Use the project-specified standard and edition; “ANSI flange” alone is not a complete purchasing description.

What to Send for Identification or Quotation

  • clear face, side-profile and marking photographs;
  • OD, bore, thickness and raised-face height;
  • PCD/BCD, bolt-hole count and hole diameter;
  • flange type and face type;
  • pipe OD and schedule/bore where relevant;
  • service fluid, design pressure and temperature;
  • required material specification, certificates and quantity.

Verified Product Starting Points

Use these product pages as quotation starting points; measurement alone does not confirm grade or service suitability.

Frequently Asked Questions

Is flange size the same as outside diameter?

No. Nominal size is a designation, not the measured flange OD. Confirm the full dimensional pattern.

Can I infer the pressure class from thickness?

Not reliably. Compare thickness together with OD, bolt pattern, face, type and bore against the specified standard and edition.

Should I measure a flange while the line is pressurized?

Only follow the site’s approved safety procedure. Never loosen bolting or disturb a live joint for identification.

Primary References

  • ASME B16.5 — published scope for pipe flanges and flanged fittings.
  • ASME B16.47 — published scope for large-diameter steel flanges.

Need Help Identifying a Flange?

Send the measurements, marking photos, face/type, quantity and service conditions. We can compare the information with the requested standard before quotation.

Request Flange Identification and a Quote

No Comments

Leave a Reply

Your email address will not be published. Required fields are marked *

HomeProducts
Search