Flanş Nedir??

Hızlı Yanıt

A flange is a projecting rim or forged, döküm, machined or fabricated component used to create an interface between pipe, vanalar, pompalar, vessels or other equipment. In a typical piping joint, two compatible flanges are aligned and bolted together with a gasket or specified sealing element. The flange is one part of the joint system; it does not make a connection automatically leak-proof.

See flange parts and terminology

What Parts Make Up a Flanged Joint?

Part or feature İşlev What must match
Flange body and hub Transfers load between the pipe/equipment and bolted joint. Tip, malzeme, boyutlar, bore and connection method.
bakan Provides the specified contact geometry for the sealing element. Kaplama tipi, finish and compatible gasket/joint design.
Cıvata dairesi ve delikler Position the bolting around the joint. Standart, nominal boyut, sınıf/PN, hole count and pattern.
Cıvatalama Applies clamping force to the joint. Malzeme, boyut, uzunluk, yağlama ve montaj prosedürü.
Conta veya halka Creates the specified seal when compressed within its design range. bakan, boyutlar, malzeme, service and assembly requirements.

What Does a Flange Do?

A flange provides a defined, separable interface. It can connect piping sections, attach piping to equipment, close an opening with a blind flange, or support an instrument or flow-measurement arrangement. The engineering result depends on the complete joint, including alignment, conta, cıvatalama, surface condition and controlled assembly.

Terminology boundary: “flange” describes a component or feature, not one universal design. Boru flanşları, ekipman nozulları, structural flanges and specialized connector systems can follow different standards.

Common Pipe-Flange Types

  • Kaynak boynu: has a tapered hub and butt-weld end.
  • Slip-on: fits over pipe and uses the specified fillet-weld arrangement.
  • Soket kaynağı: receives pipe in a socket within its applicable size/service limits.
  • Dişli: connects by thread and remains subject to thread and service restrictions.
  • Tur eklemi: backing flange used with a stub end, allowing rotation for alignment.
  • Kör: has no central bore and closes a flanged opening.
  • Delik: includes pressure-tap provisions for an orifice-meter assembly governed by its applicable standard.

Flange Face Terms

  • Yükseltilmiş yüz (RF): a raised gasket seating area defined by the applicable standard.
  • Düz yüz (FF): the contact surface is in one plane across the face.
  • Halka tipi bağlantı (RTJ): a machined groove accepts a compatible metallic ring; the specified geometry and assembly are critical.

Face type alone does not establish pressure rating or suitability. Verify the standard, malzeme, boyut, derecelendirme, gasket/joint design and mating component.

How Flanges Are Designated

A usable flange description normally includes the dimensional standard and edition, flanş tipi, NPS/DN, sınıf veya PN, malzeme özellikleri ve sınıfı, karşı karşıya, delik veya boru programı, and any supplementary inspection or documentation requirements. ASME B16.5 covers pipe flanges and flanged fittings within its stated NPS 1/2 NPS aracılığıyla 24 kapsam; ASME B16.47 addresses large-diameter steel flanges within NPS 26 NPS aracılığıyla 60.

Material Is Separate from Dimensions

The dimensional standard establishes geometry and ratings within its scope, while a material specification controls such matters as grade, kimya, heat treatment and mechanical properties. Örneğin, ASTM A182/A182M covers forged or rolled alloy and stainless-steel piping components for pressure systems, flanşlar dahil. A complete order identifies both the dimensional standard and material specification.

Stainless Steel Product Starting Points

These are real product pages for quotation review; they do not replace service-specific material selection.

Sıkça Sorulan Sorular

Is a flange the same as a fitting?

Her zaman değil. A flange can be a standalone piping component, an integral equipment feature or part of a flanged fitting. The applicable product definition and standard control.

Are all flanges bolted?

Many piping flanges form bolted joints, but “flange” is broader than one bolted pipe-connection design.

Does a flange guarantee a leak-free joint?

HAYIR. Joint performance depends on compatible components and controlled assembly.

Birincil Referanslar

  • ASME B16.5 — boru flanşları ve flanşlı bağlantı parçaları için yayınlanmış kapsam.
  • ASTM A182/A182M — published material-specification scope for forged or rolled alloy and stainless-steel piping components.

Need a Flange Quotation?

Standardı gönder, boyut, sınıf/PN, tip, malzeme kalitesi, karşı karşıya, delik, miktar, service conditions and document requirements.

Flanş Teklifi İsteyin

Hayır Yorumlar

Cevap vermek

E -posta adresiniz yayınlanmayacak. Gerekli alanlar işaretlenmiştir *

EvÜrünler
Aramak