How to Order Duplex 2205 Pipe Fittings: ASTM A815 Elbow RFQ Checklist
A complete RFQ for Duplex 2205 pipe fittings should identify the exact UNS grade, ASTM specification, fitting type, angle, radius, nominal size, wall schedule, ASTM A815 WP class, dimensional standard, end preparation, inspection scope and required documents. “Duplex 2205 elbow” alone is not a complete purchasing description.
View ASTM A815 Duplex 2205 Elbows
1. Start With the Correct Material Specification
ASTM A815/A815M covers wrought ferritic, ferritic/austenitic and martensitic stainless-steel piping fittings of seamless and welded construction. For a Duplex 2205 order, the RFQ should state the required UNS designation rather than relying only on the commercial name “2205.”
A practical material line should identify ASTM A815/A815M, the required UNS grade such as S32205, any dual-certification requirement, the applicable project specification and the required edition of each standard.
UNS S31803 and S32205 are closely related duplex grades, but they should not be treated as automatically interchangeable. If dual certification is required, it must be supported by the material certificate and the applicable specification requirements.
2. Specify the Fitting Type and Geometry
Identify the exact fitting rather than writing only “pipe fittings.” For an elbow, confirm:
- 45-degree or 90-degree elbow
- Long radius or short radius
- Equal-size or reducing configuration
- Nominal pipe size
- Wall schedule or specified wall thickness
- Required dimensional standard
- Any controlled drawing or special tangent requirement
Long-radius and short-radius elbows do not have the same center-to-end dimensions. A supplier cannot select the correct geometry from the material grade alone.
3. What Do WP-S, WP-W, WP-WX and WP-WU Mean?
ASTM A815 divides Class WP fittings into manufacturing and examination subclasses.
| Class | General meaning | Purchasing check |
|---|---|---|
| WP-S | Manufactured from seamless product by a seamless method | Confirm whether seamless construction is required |
| WP-W | Contains fabrication or construction welds covered by the radiographic requirements for this class | Confirm the accepted welded route and records |
| WP-WX | Contains welds for which all welds are radiographed | State the class explicitly when required |
| WP-WU | Contains welds for which all welds are ultrasonically examined | Confirm whether UT is accepted or required |
The class suffix is not decorative. It communicates part of the manufacturing and examination route. Do not request WP-S automatically unless the piping specification requires seamless manufacture.
4. Separate Material and Dimensional Standards
ASTM A815 addresses fitting material and manufacturing requirements. It does not replace the dimensional standard. ASME B16.9 covers factory-made wrought buttwelding fittings and includes dimensional, tolerance, marking and related requirements within its scope.
- Material specification: ASTM A815/A815M
- Material grade: required UNS designation
- Dimensional standard: applicable ASME B16.9 edition
- Project requirements: only where applicable
5. Confirm Pipe Schedule and End Preparation
The fitting bore and wall must be compatible with the connecting pipe and approved welding procedure. Include nominal pipe size, schedule or nominal wall thickness, connecting-pipe wall when needed, bevel requirement, corrosion allowance where applicable, bore matching and permitted tolerances.
For unusual wall combinations, provide the actual wall thickness and a controlled drawing instead of relying on an informal description.
6. Define Inspection and Testing Before Quotation
Inspection requirements affect manufacturing planning, documentation and price. Agree them before the purchase order is issued. Possible RFQ items include material certificates, chemical and mechanical records, heat-treatment records, dimensional inspection, PMI where required, the examination associated with the specified WP class, surface examination, third-party inspection and witness or hold points.
Do not request every available inspection by default. Select examinations required by the governing code, project specification and service risk. “NDT required” is incomplete unless the method, coverage, acceptance basis and reporting requirement are identified.
7. What Should Appear on the MTC?
Review the material certificate against the purchase order, applicable standard and delivered marking. Check the manufacturer and product identification, specification and edition, UNS grade, WP class, heat or lot identity, chemical analysis, mechanical properties, heat-treatment information, applicable examination results and traceability between the certificate, marking and packing list.
8. Duplex 2205 Elbow RFQ Checklist
- ASTM A815/A815M edition.
- Exact UNS grade and any dual-certification requirement.
- WP-S, WP-W, WP-WX or WP-WU class.
- Elbow angle and LR or SR geometry.
- Nominal size and wall schedule or thickness.
- Applicable dimensional standard and edition.
- End preparation and bore-matching requirement.
- Quantity by size and schedule.
- Inspection, NDE and witness requirements.
- MTC, heat-treatment and traceability documents.
- Marking, packaging and item-tag requirements.
- Delivery destination and requested commercial terms.
Common Purchasing Errors
Writing only “Duplex 2205 elbow”
This omits the standard, UNS grade, WP class, radius, wall and document requirements.
Assuming every 2205 fitting is seamless
ASTM A815 includes seamless and welded construction routes. Specify the applicable WP class.
Using S31803 and S32205 interchangeably
State the required UNS designation. Accept dual certification only when supported by the certificate and project requirements.
Forgetting the dimensional standard
ASTM A815 identifies the material and manufacturing specification. State the dimensional standard separately.
Frequently Asked Questions
Is WP-S always better than WP-W?
No. The correct class depends on the piping specification, manufacturing route, size, examination requirements and project approval.
Does ASTM A815 define elbow dimensions?
ASTM A815 is primarily the material and manufacturing specification. Factory-made buttwelding fitting dimensions are generally controlled by the specified dimensional standard.
Can S31803 be supplied instead of S32205?
Not without purchaser approval and verification against the applicable specification. State the exact grade and any permitted dual-certification basis.
Should the buyer request PMI?
PMI may be useful when required by the project specification or material-control procedure. Define the method, coverage, acceptance basis and reporting requirement.
Request a Technical Quotation
Send the required ASTM A815 grade, WP class, elbow angle, radius, size, schedule, quantity, dimensional standard, inspection scope and document requirements.
