ASTM B366 Hastelloy C276 Stub End

SKU: SASA-SE-N10276 Categories: ,

Lap-joint stub end in ASTM B366 WP-N10276 for aggressive chemical and chloride-resistant piping. Available with project-specific dimensions, documentation and inspection.

  • Material: ASTM B366 WP-N10276 / UNS N10276
  • Standard: ASME B16.9 / MSS SP-43
  • Quality: EN 10204 3.1 MTC, traceability and PMI when ordered

Description

Lap-joint butt-weld fitting | ASME B16.9 / MSS SP-43

ASTM B366 Hastelloy C276 Stub End

Lap-joint stub end in ASTM B366 WP-N10276 for aggressive chemical and chloride-resistant piping. Available with project-specific dimensions, documentation and inspection.

Direct answer

What is a Hastelloy C276 stub end?

A stub end is a butt-weld piping fitting used with a loose lap-joint backing flange. The stub end provides the process-wetted sealing face and weld connection, while the backing flange rotates freely behind the lap. This arrangement can simplify bolt-hole alignment and allows the backing flange material to be selected separately when the design permits.

ASTM B366 WP-N10276 is the factory-made wrought fitting designation for UNS N10276. It is appropriate for products such as butt-weld stub ends, while ASTM B462 applies to forged flanges and fittings.

The lap face, corner radius, hub length, wall thickness and weld end must suit the backing flange, gasket and connected pipe. Long-pattern and short-pattern dimensions are not interchangeable. The pressure capability belongs to the complete engineered joint, not to the stub end in isolation. The piping specification should define the material combination, corrosion allowance, weld procedure and dimensional standard.

MaterialASTM B366 WP-N10276
UNSUNS N10276
Dimensional standardASME B16.9 / MSS SP-43
Supply focusType A or specified lap-joint stub end, long or short pattern as ordered, with butt-weld end

Technical specifications

Product Stub End
Material specification ASTM B366 WP-N10276
UNS designation UNS N10276
Dimensional standard ASME B16.9 / MSS SP-43
Size range Standard and project-specific sizes within the selected ASME B16.9 or MSS SP-43 dimensional range
Rating / schedule Wall schedule and backing-flange rating selected for the complete lap-joint assembly
Configuration Type A or specified lap-joint stub end, long or short pattern as ordered, with butt-weld end
Documentation EN 10204 3.1 MTC, heat-number traceability, dimensional report and PMI when ordered
Optional inspection PMI, PT, UT where applicable, corrosion testing and third-party inspection when specified

Final dimensions, ratings, tests and acceptance criteria follow the purchase order, approved drawing, applicable code and specified standard edition.

Why specify Hastelloy C276?

N10276 is selected for resistance to many aggressive chemical environments, including selected reducing and oxidizing media. Its high molybdenum content supports localized-corrosion resistance, while chromium contributes in oxidizing conditions.

Clean fabrication, controlled thermal practice and compatible filler selection are important. Iron contamination and poor surface preparation should be avoided for corrosion-critical equipment.

Procurement checkpoint: Use UNS N10276 and the correct ASTM product-form specification. “Hastelloy” alone identifies a family of alloys and is not a complete purchase description.

Typical applications

Acid chemical processingCorrosive chemical transfer lines
Pollution-control equipmentSeawater and desalination piping
Chloride process pipingProcess skids requiring easier bolt alignment
Pulp and specialty chemical systemsHigh-alloy piping where backing-flange economy is evaluated

These are selection examples, not universal suitability claims. Verify corrosion, temperature, pressure, fabrication and code requirements for the actual service.

Ordering and specification guidance

State the fitting material designation, UNS number, NPS, wall schedule, dimensional standard, pattern, lap-face requirements and mating backing flange. For nickel-alloy and duplex products, confirm whether seamless or welded construction and the applicable ASTM class marking are required.

Define the product form, heat treatment, PMI, PT, corrosion test and any low-iron contamination controls required by the project.

Engineering selection boundaries

Material grade, nominal size and pressure class are necessary purchasing inputs, but they do not prove suitability by themselves. The responsible piping engineer should verify the design code, design pressure and temperature, corrosion allowance, connected pipe dimensions, flange facing, gasket system, bolting, welding procedure and examination plan as one coordinated specification. Service chemistry, concentration, contaminants, velocity, shutdown conditions and cleaning media can change corrosion performance. Request written confirmation against the project datasheet and approved drawing before manufacture, especially where sour service, seawater exposure, cyclic loading, vacuum, lethal service or regulatory inspection applies.

Manufacturing, inspection and traceability

Inspection covers chemistry and heat-treatment certification, wall thickness, lap outside diameter, face thickness, corner radius, overall length, weld-end preparation and surface condition. PMI and PT can be specified for corrosion-resistant alloys.

Certificate review and PMI verify alloy identity; PT helps screen machined surfaces for relevant indications before release.

Material controlHeat-number traceability and certificate review.
Dimensional controlRecorded checks against the drawing and ordered standard.
Surface examinationVisual inspection and PT when specified.
Release packageMTC and agreed inspection records before shipment.

Official standards and engineering references

Use the current project-approved editions. The following official scope pages help procurement teams separate dimensional requirements from material requirements.

Related stub end products

Browse the complete Stub Ends category ->

RFQ checklist

  1. ASTM grade and UNS designation
  2. NPS and pipe schedule
  3. ASME B16.9 or MSS SP-43
  4. Long or short pattern
  5. Type and lap-face dimensions
  6. Backing-flange material and class
  7. Seamless or welded construction
  8. MTC, PMI, PT and inspection

Frequently asked questions

Does a stub end include the backing flange?

Not unless the purchase order states it. A stub end and a lap-joint backing flange are separate components and may use different material specifications.

What is the difference between long-pattern and short-pattern stub ends?

They have different overall lengths and assembly considerations. The required pattern must be stated and matched to the project dimensional standard.

Can a carbon steel backing flange be used with an alloy stub end?

It can be considered when the design, environment, corrosion protection, temperature and piping code allow it. The project engineer must approve the material combination.

What is the UNS number for Hastelloy C276?

The UNS designation is N10276.

Which ASTM specifications cover C276 components?

ASTM B462 commonly covers forged flanges and fittings, while ASTM B366 covers factory-made wrought welding fittings. Match the specification to the product form.

Request a technical quotation

Send the material grade, standard, size, rating or schedule, quantity and inspection requirements. SASA FLANGE will review the complete specification before quotation.

Contact SASA FLANGE View category

Leave Your Message

    Send your size, material, standard and quantity. We will reply within 24 hours.

    Upload Image / Drawing (optional)

    Accepted: JPG, PNG, WebP or PDF. Maximum file size: 5 MB.