산업용 배관 시스템, 그만큼 플랜지면 is one of the most critical sealing surfaces. Whether you’re manufacturing a new flange or restoring an old one, the accuracy of flange face machining directly determines the integrity of your piping connections. Done properly, it ensures long-term sealing performance and compliance with global standards. Done poorly, it can lead to leaks, 시스템 오류, and costly downtime.

그래서, how do you machine a flange face correctly? 이 기사에서는, we’ll walk you through the entire process — from surface preparation to tool selection, machining techniques, 그리고 최종 점검. Whether you’re a plant maintenance engineer, fabricator, or QC inspector, this guide provides everything you need to know.

SASA FLANGE, a trusted global manufacturer of precision flanges, ensures that every flange face we produce is machined to perfection — according to ASME, EN, and customer-specific standards.

---

What Is a Flange Face and Why It Must Be Machined Accurately

에이 플랜지면 is the contact surface that mates with a gasket or another flange in a piping system. It ensures pressure sealing when bolts are tightened. Over time or during manufacturing, imperfections on this surface can lead to sealing failures.

Key goals of flange face machining:

• Achieve correct 평탄 그리고 병행

• Create the right surface roughness for gasket grip

• Ensure 치수 정확도 within tolerance

• Avoid leakage under pressure or temperature fluctuations

The type of gasket used (예를 들어, spiral wound, 고무, PTFE) determines what finish and texture are required.

---

Common Flange Face Types

Before machining, identify the face type to apply the correct method:

1. 제기된 얼굴 (RF)

• Most common type in ASME flanges

• Requires a spiral serrated or stock finish

2. 편평한 얼굴 (FF)

• Must be entirely flat for soft gasket sealing

• Used in low-pressure systems

3. 링형 조인트 (RTJ)

• Features a machined groove for metallic gaskets

• Requires high-precision CNC contouring

4. Male-Female and Tongue & 홈

• Requires alignment of corresponding profiles

• Used in high-seal, alignment-critical systems

SASA FLANGE manufactures all these flange face types, precisely machined to required tolerances and surface finishes.

---

Tools and Equipment Needed

Flange face machining can be done either in a factory setting or on-site. The tools used depend on the application and flange size:

🛠 Factory CNC Machining Tools:

• Horizontal lathes

• Vertical turning lathes (VTL)

• CNC boring and facing machines

• Surface profilometers

🛠 Portable On-Site Facing Machines:

• ID or OD-mounted flange facing machines

• Magnetic or hydraulic base units

• Hand-held rotary tools (for light resurfacing)

The machining tool must be rigid, vibration-free, and capable of producing the desired surface finish.

---

Step-by-Step Guide: 플랜지 면을 가공하는 방법

단계 1: Clean and Inspect the Flange

Remove all dirt, 부식, 규모, and old gasket residue. Visually inspect for:

• Deep pitting or grooves

• Warping or distortion

• Rust around bolt holes or face

If the damage is minor, machining may proceed. If severe, replacement is advised.

---

단계 2: Set Up the Flange Securely

• If machining in-shop, mount the flange firmly in a lathe or CNC chuck.

• For in-situ repair, align and clamp the portable machine accurately to the flange’s center.

• Verify flatness using a dial indicator.

Proper alignment prevents uneven cuts and off-center faces.

---

단계 3: Select the Right Cutting Tool and Feed Rate

• For spiral serrated finishes: Use a radial feed tool and advance at a slow, consistent rate (일반적으로 0.8 mm/rev for ASME stock finish).

• For smooth finishes: Use a fine insert and slower feed rate.

• For RTJ: Use a form tool matching the groove profile.

Tool material should match the flange’s hardness — carbide inserts for stainless steel or hardened alloy flanges.

---

단계 4: Begin Machining

• Start from the center and move outward in a spiral path.

• Keep spindle RPM within optimal limits (예를 들어, 60–120 RPM depending on size).

• Monitor chip formation, tool wear, 표면 품질.

Use coolant as needed to minimize heat and improve finish.

---

단계 5: Measure Surface Finish and Flatness

Once machining is complete:

• 사용 surface roughness tester (profilometer) to measure AARH (Arithmetic Average Roughness Height).

  • Common standards:

    • 125–250 AARH (stock finish for spiral wound gaskets)

    • ≤ 125 AARH (smooth finish for soft gaskets)

• 확인하다 평탄 with a straight edge and feeler gauge or laser alignment tools.

• Verify face thickness and bore diameter match specifications.

---

단계 6: Apply Anti-Corrosion Coating (필요한 경우)

In corrosive environments, apply:

• Rust preventive oil

• Epoxy paint (on non-sealing surfaces)

• PTFE spray or film (for marine or chemical service)

Do ~ 아니다 coat the actual sealing face unless specified by the gasket or application.

---

Machining Tips for Optimal Results

• Always machine with a new or freshly sharpened tool for critical flanges

• 사용 bore-matched flanges to minimize turbulence and erosion

• Maintain correct tool overhang to avoid chatter

• Recheck machine calibration before precision jobs

• Ensure gasket seating width is not altered during resurfacing

---

Standards That Govern Flange Face Machining

The following global standards specify machining tolerances and finishes:

• ASME B16.5 / B16.47 (U.S.)

• EN 1092-1 (유럽)

• MSS SP-6 – Finish and marking specifications

• API 6A – High-pressure flange faces in oil & 가스

• ISO 7005 – International flange standard

SASA FLANGE adheres to these standards in all flange production and provides full documentation (EN 10204 3.1/3.2) 요청 시.

---

Applications That Require Precision Machined Flange Faces

Machined flange faces are critical in:

• 정유공장 및 화학공장

• 발전 (steam and nuclear)

• 음식, beverage, and pharmaceutical industries

• Cryogenic and high-temperature systems

• Hydraulic and high-pressure equipment

In any system where sealing failure is unacceptable, machining precision is non-negotiable.

---

왜 선택해야 할까요? SASA FLANGE for Precision-Machined Flanges?

~에 SASA FLANGE, every flange face is machined using advanced CNC equipment and verified by trained inspectors to meet:

• Exact surface finish specifications (spiral serrated, 매끄러운, RTJ groove)

• Flatness and parallelism tolerances

• Pressure class and dimensional conformity

We supply carbon steel, 스테인레스 스틸, 듀플렉스, and nickel alloy flanges in all sizes and standards, ready for use in demanding projects worldwide.

SASA FLANGE — Where Every Surface Counts. Engineered for Excellence.

---

결론

그래서, how do you machine a flange face? With the right tools, methods, and quality controls, you can restore or create a flange surface that ensures leak-proof sealing and long-term system performance.

Whether manufacturing a new flange or resurfacing an existing one, the process requires skill, 표준 준수, and precision machining — all of which are at the core of what we do at SASA FLANGE.

For guaranteed performance, certified accuracy, and professional support, 신뢰하다 SASA FLANGE to deliver your next critical connection.