• Blogue
  • Notícias
  • Inspeção de terceiros concluída para flanges ASTM A182 F22
Inspetor de qualidade verificando componentes forjados acabados
3 Agosto 2026

Inspeção de terceiros concluída para flanges ASTM A182 F22

Notícias do projetoPublished: 3 Agosto 2026SASA FLANGE Project Team
Project completed

Third-party inspection has been completed for an ASTM A182 F22 flange order. The independent inspector reviewed traceability and material records, witnessed selected verification activities and confirmed dimensional, EQM, marking and packing requirements against the approved inspection and test plan.

Project snapshot

Project status Third-party inspection completed
Material ASTM A182 F22 forged alloy steel
Flange type Pescoço de solda, slip-on and blind
Padrão ASME B16.5
Pressure class Class 300–900
Faixa de tamanho NPS 2–16
Inspeção MTC review, PMI, dureza, UT, dimensões, marking and packing
Application Petrochemical process piping

Delivery highlights

Hold and witness points followed the purchaser-approved ITP.
Physical markings were cross-checked against heat and inspection records.
Release was documented before preservation and packing were closed.

What the independent inspector reviewed

The review began with the purchase order, approved drawings, material certificates and inspection and test plan. Heat numbers on the flanges were matched to records before selected PMI, hardness and NDE results were accepted. Calibration status and report identification were included in the document review.

Dimensional inspection covered the characteristics identified by flange type, including drilling, enfrentando, thickness, hub or bore details and marking. The inspector also reviewed the visible condition of gasket faces and weld preparations.

From inspection release to packing

Third-party involvement does not transfer design responsibility or replace the manufacturer’s quality system. It provides independent evidence that the defined hold or witness points were completed. Any observations are resolved through the project procedure before release.

After acceptance, sealing faces were covered and the packing list was reconciled with the released quantities and identification. Inspection records were compiled into the final manufacturing record book as required.

Information needed for a comparable RFQ

A comparable inquiry should identify the exact material specification and grade, governing standard and edition, NPS, classe de pressão, tipo de flange, enfrentando, cronograma de furo ou tubo correspondente, quantity and destination. For this project-news scope, the key reference points were ASTM A182 F22 forged alloy steel, Pescoço de solda, slip-on and blind, Class 300–900 e NPS 2–16.

State the required EN 10204 certificate type, rastreabilidade do número de calor, PMI extent, limites de dureza, relatório dimensional, NDE method and acceptance standard, third-party witness points, packing method and required delivery date at quotation stage. Early definition allows manufacturing, inspection and document schedules to be reviewed together.

Production, inspection and packing photos

Images show the relevant SASA FLANGE production, quality-control and shipment stages used for this project-news report.

Finished alloy steel flanges presented for inspection
Machined flanges staged for final verification.
Ultrasonic examination during quality control
NDE records reviewed at the project hold point.
Accepted components prepared for export packing
Packing followed inspection release.
Métodos de inspeção END para flanges de liga de aço forjado Por que o teste PMI é importante para flanges de liga de aço What Should an EN 10204 3.1 Certificado de material inclui?

Perguntas frequentes

Does third-party inspection replace the manufacturer’s inspection?

Não. It independently witnesses or reviews defined activities; the manufacturer remains responsible for its quality controls and contractual compliance.

What is an ITP hold point?

A hold point is a stage that cannot proceed until the required party has reviewed or released it under the approved inspection and test plan.

Can the inspection scope be added after production?

Some reviews may be possible, but witness points and test extent should be agreed before manufacturing to avoid unavailable evidence or rework.

Request a quotation for alloy steel flanges

Send the ASTM grade, padrão e edição, NPS, classe de pressão, tipo de flange, enfrentando, cronograma de furo ou tubulação, quantidade, delivery destination and required PMI, EQM, dureza, third-party inspection and documentation.

Send Your RFQView Flange Products

Posts Relacionados

CasaProdutos
Procura