ASTM B366 Alloy 625 180 Degree Elbow / Return Bend

SKU: SASF-B366-N06625-180 Categories: ,

ASTM B366 Alloy 625 180 degree elbows, also called return bends, reverse a butt-welded piping run while keeping both ends parallel. The RFQ must define the ordered grade, fitting class, geometry, wall, ends and inspection requirements.

  • Material: Alloy 625 / UNS N06625 under ASTM B366/B366M
  • Dimensional basis: ASME B16.9 or an approved project drawing
  • Define in the RFQ: size, wall, radius, center-to-center, tangents and ends
  • Supply boundary: quotation and documents are confirmed for the order

Description

UNS N06625 wrought return fitting

ASTM B366 Alloy 625 180 Degree Elbow

A procurement page for a factory-made wrought butt-weld return fitting. Final suitability depends on the complete service environment, geometry, fitting class, construction route, connected pipe and governing design documents.

Request a Technical Quote

Quick specification answer

An ASTM B366 Alloy 625 180 degree elbow is a factory-made wrought nickel-alloy fitting used to reverse a butt-welded piping run through 180 degrees. ASTM B366/B366M covers the material and fitting requirements for nickel and nickel-alloy fittings, including 180-degree bends. ASME B16.9 provides the dimensional framework for factory-made wrought butt-welding fittings within its scope.

The grade and angle are not a complete purchase description. State NPS or DN, wall or Schedule, return radius, center-to-center dimension, tangent length, fitting class, seamless or welded construction as applicable, end preparation, quantity and required inspection records.

Specification boundary: Alloy 625 / UNS N06625 identifies the ordered material family. It does not prove a fixed size range, manufacturing route, test result or service guarantee. The purchase order and approved design documents govern.

Product and ordering basis

Product form Factory-made wrought 180° butt-weld elbow / return bend
Material designation ASTM B366/B366M Alloy 625; UNS N06625; order-specific fitting grade and class must be stated
Dimensional basis ASME B16.9 where applicable, or an approved project drawing for special geometry
Ends Butt-welding ends prepared to the ordered piping specification
Wall definition Schedule, nominal wall or minimum ordered wall; mating pipe dimensions must be stated
Return geometry Long radius, short radius or drawing-specific radius; confirm center-to-center and tangents
Construction and class State the ASTM B366 fitting class and seamless or welded route required by the purchase specification
Inspection scope Visual, dimensional, material documentation and additional examination only as ordered and confirmed

This table lists RFQ variables. It is not a declaration of stock, range, certificates, test results, capacity or lead time.

Return geometry controls fit-up

Radius

Long- and short-radius returns occupy different space and affect fit-up. Specify the required radius rather than inferring it from the angle.

Center-to-center

This dimension controls the spacing between the parallel pipe runs and must match the equipment or piping layout.

Tangent length

Straight extensions may be needed for welding access or fabrication. They are not automatically part of every return fitting.

Wall and alignment

Check ordered wall, end dimensions, roundness and alignment against the applicable standard or approved drawing.

Alloy 625 selection boundary

UNS N06625 is a nickel-chromium-molybdenum-niobium alloy considered for combinations of corrosion resistance and mechanical strength. A fitting purchase still requires service-specific engineering review. Temperature, chlorides, acids, concentration, contaminants, crevices, velocity, cycling, fabrication and design life can change the suitability decision.

Do not select the return bend from the grade name alone. Confirm compatibility with the connected pipe and filler-metal procedure, the applicable piping code, the required ASTM B366 fitting class, heat treatment and examination requirements, and the project acceptance criteria.

Inspection and acceptance points

Identity and traceability

Verify grade, fitting class, heat identity, marking, standard edition and document references against the purchase order.

End compatibility

Check outside diameter, ordered wall, bevel details and compatibility with the mating pipe before fabrication.

Return dimensions

Check angle, radius, center-to-center spacing, end alignment and tangent length against the standard or drawing.

Examination records

Define material certificates, dimensional reports and any additional NDE in the RFQ. Scope must be confirmed for the order.

RFQ checklist

  1. ASTM B366/B366M edition, UNS N06625 designation and required fitting class
  2. ASME B16.9 edition or approved dimensional drawing
  3. NPS or DN and mating pipe outside diameter
  4. Schedule, nominal wall or minimum wall requirement
  5. Long radius, short radius or exact centerline radius
  6. Center-to-center dimension and required tangent length
  7. Butt-weld end preparation and matching pipe specification
  8. Quantity, service conditions and governing design code
  9. Material certificate, dimensional report, NDE and third-party inspection requirements

Frequently asked questions

Is a 180-degree elbow the same as a return bend?

The terms are commonly used for a fitting that reverses pipe direction. The RFQ must still define radius, center-to-center, tangents, wall and governing standard.

Does ASTM B366 define every dimension?

No. ASTM B366/B366M defines material and fitting requirements. Dimensions are commonly ordered to ASME B16.9 or an approved project drawing.

Can the page confirm seamless or welded construction?

No. The required route and examination depend on the ordered fitting class, dimensions and project requirements.

Are certificates and NDE reports automatically included?

No. List every required document and examination in the RFQ so the applicable scope can be reviewed before quotation.

Technical references

The technical boundary was checked against active ASTM B366/B366M-25 and ASME B16.9-2024 official scopes. The editions stated in the purchase order govern the supplied product.

Prepare an Alloy 625 180° return bend RFQ

Send size, wall, radius, center-to-center, tangents, ends, fitting class, quantity and inspection requirements for quotation review.

Send Your Requirements
View 180° Elbow Category

Leave Your Message

    Send your size, material, standard and quantity. We will reply within 24 hours.

    Upload Image / Drawing (optional)

    Accepted: JPG, PNG, WebP or PDF. Maximum file size: 5 MB.