ASTM A182 F22 플랜지에 대한 제3자 검사 완료
Third-party inspection has been completed for an ASTM A182 F22 flange order. The independent inspector reviewed traceability and material records, witnessed selected verification activities and confirmed dimensional, 임사체험, marking and packing requirements against the approved inspection and test plan.
Project snapshot
| Project status | Third-party inspection completed |
|---|---|
| 재료 | ASTM A182 F22 forged alloy steel |
| 플랜지형 | 용접 목, slip-on and blind |
| Standard | ASME B16.5 |
| Pressure class | Class 300–900 |
| 크기 범위 | NPS 2–16 |
| 점검 | MTC review, PMI, 경도, UT, 치수, marking and packing |
| Application | Petrochemical process piping |
Delivery highlights
What the independent inspector reviewed
The review began with the purchase order, approved drawings, material certificates and inspection and test plan. Heat numbers on the flanges were matched to records before selected PMI, hardness and NDE results were accepted. Calibration status and report identification were included in the document review.
Dimensional inspection covered the characteristics identified by flange type, including drilling, 깃 달기, 두께, hub or bore details and marking. The inspector also reviewed the visible condition of gasket faces and weld preparations.
From inspection release to packing
Third-party involvement does not transfer design responsibility or replace the manufacturer’s quality system. It provides independent evidence that the defined hold or witness points were completed. Any observations are resolved through the project procedure before release.
After acceptance, sealing faces were covered and the packing list was reconciled with the released quantities and identification. Inspection records were compiled into the final manufacturing record book as required.
Information needed for a comparable RFQ
A comparable inquiry should identify the exact material specification and grade, 관리 표준 및 에디션, NPS, 압력 등급, 플랜지형, 깃 달기, 보어 또는 일치하는 파이프 일정, quantity and destination. For this project-news scope, the key reference points were ASTM A182 F22 forged alloy steel, 용접 목, slip-on and blind, Class 300–900 그리고 NPS 2–16.
State the required EN 10204 certificate type, heat-number traceability, PMI extent, 경도 한계, 치수 보고서, NDE method and acceptance standard, third-party witness points, packing method and required delivery date at quotation stage. Early definition allows manufacturing, inspection and document schedules to be reviewed together.
Production, inspection and packing photos
Images show the relevant SASA FLANGE production, quality-control and shipment stages used for this project-news report.
Related technical guides
자주 묻는 질문
Does third-party inspection replace the manufacturer’s inspection?
아니요. It independently witnesses or reviews defined activities; the manufacturer remains responsible for its quality controls and contractual compliance.
What is an ITP hold point?
A hold point is a stage that cannot proceed until the required party has reviewed or released it under the approved inspection and test plan.
Can the inspection scope be added after production?
Some reviews may be possible, but witness points and test extent should be agreed before manufacturing to avoid unavailable evidence or rework.
Request a quotation for alloy steel flanges
Send the ASTM grade, standard and edition, NPS, 압력 등급, 플랜지형, 깃 달기, 보어 또는 파이프 일정, 수량, delivery destination and required PMI, 임사체험, 경도, third-party inspection and documentation.
관련 게시물
ASTM A182 F51 대 F60 플랜지: S31803 대 S32205 설명
ASTM A182 F51 및 F60 이중 플랜지 비교, S31803/S32205 포함…
UNS S32750 대 S32760 플랜지: ASTM A182 F53 또는 F55?
S32750 및 S32760 슈퍼 듀플렉스 플랜지 비교, ASTM A182 포함…
